Wire and cable product category

1. Power supply system

Power supply system selection of cable and wire commodity key empty frame bare cable, medical bus bar (busbar), wire and cable (plastic cable, tinfoil force cable (basically replaced by plastic wire and cable), rubber sheath cable, empty frame insulated wire), branch cable (replace part of the busbar), special cable and electrical equipment with electrical equipment weapons equipment cable and wire.

2. Information content transmission system software

The key cables and wires used for information content transmission system software include local telephone cables, television cables, electronic device cables, radio frequency coaxial cables, optical fiber cables, data information cables, special cables, power engineering communications or other composite cables.

3, industrial equipment, instrument equipment system software

In addition to the bare cable of the empty frame, basically all other commodities are used, but mainly wire and cable, special cable, data information cable, instrument equipment cable, etc.

Cable and wire testing instrument machine equipment

ZY6014D whole bundle cable vertical ignition tester

ZY6014D whole bundle cable lighting tester is strictly manufactured in accordance with GB/T18380.31-2008 and other specifications, used to identify the vertical installation of the whole bundle of cable wire or optical cable under the required standards to prevent the vertical spread of flame working ability; It is used to measure the flame retardant grade of flame retardant cable.

The flame retardant grade of the whole bundle cable conforms to the flame retardant grade of GB/T19666-2019

The non-metallic material volume of the specimen is 7L/m, and the fire supply time is 40mm.

The non-metallic material volume of the specimen is 3.5L/m, and the fire supply time is 40mm.

The non-metallic material volume of the specimen is 1.5L/m, and the fire supply time is 20mm.

The non-metallic material volume of the specimen is 0.5L/m, and the fire supply time is 20mm.

Strictly in accordance with GB/T18380.31-2008 design scheme, GB/T18380.33, GB/T18380.34, GB/T18380.35, GB/T18380.36 experimental methods.

Machinery and equipment components:

1, wire and cable wholesale manufacturers test equipment

a) Environmental test chamber: The test equipment is an independent shell with a width of (1000±100)mm, a depth of (2000±100)mm and a height of (4000±100)mm.

b) The thermal conductivity of the wall and both sides of the environmental test chamber should be about 0.7W. m-2? K-1 thermal insulation layer, 1.5mm thick USU304 stainless steel plate, the middle is covered with 65mm thick thermal insulation phenolic insulation board, 1.5mm thick USU304 stainless steel plate.

2, air energy heat pump:

a), the air inlet is equipped with a digital display gas rate wind speed meter, the gas pressure of the gas is (5000±500)L/min;

b) After the end of the experiment: if the test piece is still lit one hour after the termination of the fire supply, it is equipped with an alarm and the equipment to forcibly terminate the lighting of the rain;

3, the type of steel ladder: wide (500±5)mm basic steel ladder width (800±10)mm wide steel ladder material is USU304 stainless steel;

4, discharge purification equipment:

a) The upper end of the environmental test chamber is equipped with a digital display anemometer to ensure that the water flow of the wind is lower than 8M/S, which is not easy to harm the total gas flow in the test chamber;

b), smoke collection and dust cleaning equipment: use SUS304 stainless steel plate, diameter of 800mm height to width ratio of 3500mm.

5. Ignition source:

a), type: The ignition source shall include one or two belt propane gas natural gas furnaces and supporting facilities steam flow meters and venturi tube switching valves. The fire supply surface should be drilled with 242 flat metal sheets with a diameter of 1.32mm, the management center spacing of such holes is 3.2mm, divided into three rows of overlapping sequence, each row of 81, 80 and 81, spread over the tolerance specification of 257×4.5mm. In addition, a row of small round holes are opened on each side of the fire spitting plate, which can maintain the smooth ignition of the flame.

b) Each gas furnace is equipped with accurate equipment to control the propane gas and gas injection rate. Can choose flowmeter or flowmeter.

6. Ignition source:

a), the gas furnace should be placed horizontally, away from the front surface of the cable test specimen (75±5)mm, away from the bottom of the environmental test chamber (600±5)mm, and symmetrical with the center line of the steel ladder. The gas furnace ignition point should be located in the management center between the two cross crotches of the steel ladder, and less than 500mm from the bottom of the specimen.

Qingdao Tianxing Cable Co., Ltd. focuses on the production of customized wire and cable manufacturers, main: fire wire and cable, power cable, control cable and other products, exported to more than 40 countries and regions around the world, the annual production capacity of 1 billion yuan. 6000 square meters of storage, standing hundreds of millions of inventory, order demand for rapid distribution and delivery, large prices more favorable. Hotline: 16678668098